3" 2010-2012 Dodge Ram 3500 4wd (w/Diesel Engine) Commuter Lift System by Carli Suspension

Carli Suspension's CS-DEL-10 Extended 10mm Front Sway Bar End Links for the Dodge Ram 2500 are crafted from premium 17-4 stainless steel. These adjustable end links guarantee a lifetime of use due to their superior material. 

• Adjustable length allows for fitment from stock height up to 3 inches of front lift
• 17-4 Machined Stainless Steel
• Eliminates sway bar binding on lifted models
• 10mm sway bar end links
• 1/2" FK Chromoly Rod end
• Fits 15mm or 16mm upper sway bar link nuts
• Carli provides a Limited Lifetime Warranty

Carli Suspension's CS-DEL-10-12mm Extended 12mm Front Sway Bar End Links for the Dodge Ram 2500 are crafted from premium 17-4 stainless steel. These adjustable end links guarantee a lifetime of use due to their superior material.

• Adjustable length allows for fitment from stock height up to 3 inches of front lift
• 17-4 Machined Stainless Steel
• Eliminates sway bar binding on lifted models
• 12mm sway bar end links
• 1/2" FK Chromoly Rod end
• Fitment – factory 18mm upper sway bar link nut
• Carli provides a Limited Lifetime Warranty

For optimal ride quality, the Torsion Sway Bar is a great choice. This enhanced sway bar effectively reduces the front sway bar's spring rate, resulting in a ride experience akin to independent suspension.

• Easily the best "bang for the buck" upgrade for ride quality
• Allows front suspension to move freely without giving up control

Carli Suspension's CS-CA-MS-10 Extended Control Arm Kit for the Dodge Ram 2500 are designed for models lifted 3 inches in the front to re-center the front axle.

• Re-centers front axle on 3" suspension kits
• Joint assembly machined with a 17-4 Stainless ball center
• Includes Energy Suspension bushings
• Box 0.120" wall mild steel construction
• Includes 4 Arms, 2 upper, 2 lower
• Zerk fittings for ease of servicing
• Serviceable, Vibration damping joints with stainless ball centers
• Carli provides a Limited Lifetime Warranty

Carli Suspension's CS-DBCA-10 High Clearance Extended Control Arm Kit for the Dodge Ram 2500 are designed for models lifted 3 inches in the front to re-center the front axle while maximizing tire clearance.

• Re-centers front axle on 3" suspension kits
• Joint assembly machined with a 17-4 Stainless ball center
• Includes Energy Suspension bushings
• 6061 Billet Aluminum Construction
• Arms are designed for maxiumum tire clearance
• Allows for 37 inch diameter tires (9" wide wheel, 5.75" BS) on 3 inch lift kits
• Includes 4 Arms, 2 upper, 2 lower
• Zerk fittings for ease of servicing
• Serviceable, Vibration damping joints with stainless ball centers
• Carli provides a Limited Lifetime Warranty

Carli Suspension's "Low Mount" Steering Stabilizer for the Dodge Ram 2500 will bolt into the factory location, replacing the OEM unit.  However, this is not your average replacement steering stabilizer. These Carli stabilizers feature an adjustable nitrogen charge that push's to the Left to counter-act a Right Hand Tire Pull (commonly caused by larger tires).  Pre-pressurized at 200 PSI (best for push effect), this stabilizer is equipped with a Schrader valve that allows customers to bleed the pressure to desired PSI.

• Improves handling - Increased steering predictability, minimized volatility and reduced driver fatigue
• Higher nitrogen charge pushes to the left to counter-act a right hand tire pull (common with larger tires)
• IFP design (Internal Floating Piston)
• 304 Stainless Steel Body with Aluminum Top-Cap
• Billet Aluminum rod ends with 1/2 inch bearings
• 17-4 stainless high-misalignment pin inside a 1/2 inch bearing for bind free performance
• Adjustable Nitrogen Charge - Schrader valve allows customer to bleed the pre-charged stabilizer (pressurized at 200 psi for right push, or drop to 70 psi for no directional influence)
• Direct bolt-on replacement for factory OEM stabilizer

Carli Suspension's CS-DHMSS-03-T "High Mount" Steering Stabilizer for the Dodge Ram 2500 is a bolt-on upgrade that works with the factory OEM or Carli Low Mount Stabilizer. This stabilizer is mounted above factory location (tie-rod) and instead mounted to the drag link and chassis (near the sway bar frame mount). This Carli stabilizer features an adjustable nitrogen charge that push's to the Left to counter-act a Right Hand Tire Pull (commonly caused by larger tires).  Pre-pressurized at 200 PSI (best for push effect), this stabilizer is equipped with a Schrader valve that allows customers to bleed the pressure to desired PSI.

• Improves handling - Increased steering predictability, minimized volatility and reduced driver fatigue
• Higher nitrogen charge pushes to the left to counter-act a right hand tire pull (common with larger tires)
• IFP design (Internal Floating Piston)
• Includes all required brackets and hardware
• 304 Stainless Steel Body with Aluminum Top-Cap
• Billet Aluminum rod ends with 1/2 inch bearings
• 17-4 stainless high-misalignment pin inside a 1/2 inch bearing for bind free performance
• Adjustable Nitrogen Charge - Schrader valve allows customer to bleed the pre-charged stabilizer (pressurized at 200 psi for right push, or drop to 70 psi for no directional influence)
• Corrects right tire pull, adjustable

This Carli Suspension CS-DSSOSK-T Opposing Steering Stabilizer kit for the Dodge Ram 3500 encompasses both the Low-Mount and High Mount Stabilizers, along with the addition of the Differential Guard and Bracket. The Differential Guard and Bracket serve the purpose of offering an alternative method for installing the low-mount stabilizer, thereby altering its corrective orientation.

• Improves handling - Increased steering predictability, minimized volatility and reduced driver fatigue
• True opposing steering stabilizer setup, high and low mount
• Higher nitrogen charge pushes to the left and right to counter-act a right or left hand tire pull (common with larger tires). Each stabilizer pushes the opposite direction, can reduce charge in one to increase push in a single direction
• Adjustable Nitrogen Charge - Schrader valve allows customer to bleed the pre-charged stabilizer (pressurized at 200 psi for right push, or drop to 70 psi for no directional influence)
• IFP design (Internal Floating Piston)
• Includes all required brackets and hardware
• 304 Stainless Steel Body with Aluminum Top-Cap
• Billet Aluminum rod ends with 1/2 inch bearings
• 17-4 stainless high-misalignment pin inside a 1/2 inch bearing for bind free performance
• Adjustable Nitrogen Charge - Schrader valve allows customer to bleed the pre-charged stabilizer (pressurized at 200 psi for right push, or drop to 70 psi for no directional influence)
• Fits Lifted or Leveled vehicles only